- Home
- Spoke length calculator for your wheel
Spoke length calculator for your wheel
Spoke length calculator for your wheel
Building a wheel yourself? This spoke length calculator makes it easy. Enter the sizes of your rim and hub and you will see straight away which spokes you need on the left and right.
Enter your sizes
You need the rim ERD, the number of spokes and the sizes of the hub.
The result at once
The length for left and right appears as you type, to a tenth of a millimetre.
With an explanation
Read how to measure, how many crossings to choose and how to round the result.
On this page
1Calculate spoke length
Enter the sizes of your rim and hub. The spoke length for the left and right side appears straight away. Nothing is sent or stored; the calculation happens in your own browser.
2Which sizes do you need?
For a good calculation you need six details. You measure four of them for each side of the hub.
- Rim ERD. The effective rim diameter: the distance between the points where the spoke ends sit in the nipples, straight through the centre of the wheel.
- Number of spokes. Count the holes in the rim. The hub must have the same number of holes.
- Flange pitch circle. The diameter of the circle through the centres of the spoke holes in the flange.
- Distance from the hub centre to the flange. This is often different on the left and right.
- Number of crossings. How often a spoke crosses other spokes from the same flange on its way to the rim.
- Spoke hole diameter. Usually 2.6 millimetres.
Many makers list these sizes in the specifications of their rims and hubs. If you do not have them, you measure them yourself.
3How do you measure the rim and hub?
- ERDThread a nipple onto two old spokes until the end of the thread is level with the slot. Put them in two holes directly opposite each other, pull them towards each other and measure the distance between the ends. Add the length of both spokes.
- Pitch circleMeasure from the centre of one spoke hole to the centre of the hole directly opposite. Do this for both flanges.
- Centre to flangeMeasure the fitting width of the hub, from locknut to locknut, and divide it by two. Subtract the distance from the locknut to the centre of the flange.
- CheckMeasure everything twice. An error of a few millimetres in the ERD gives a spoke that is just too long or too short.
Use callipers if you have them. A tape measure works too, but then checking your measurements matters even more.
4How many crossings do you choose?
The number of crossings decides how steeply the spokes are angled. More crossings give longer spokes that pass on pedalling and braking forces better.
- Three crossings is the usual choice for wheels with 32 or 36 spokes.
- Two crossings are common on wheels with 24 or 28 spokes.
- Radial (no crossings) is only possible for a wheel that gets no drive or braking force through the hub, and only if the hub maker allows it.
The calculator warns you if the number of crossings does not suit the number of spokes.
5Why are left and right different?
On a rear wheel the sprockets sit on the right. That puts the right flange closer to the centre of the hub than the left one. The spokes on that side are steeper and slightly shorter. On a front wheel with a disc brake the same happens on the side of the rotor.
That is why you enter the pitch circle, the distance to the flange and the number of crossings for each side separately. On a front wheel with rim brakes both sides are usually the same.
6How do you round the result?
Spokes are sold in whole millimetres, often in steps of one or two millimetres. The calculator shows the result to a tenth of a millimetre and gives the nearest whole size below it.
- If you are exactly between two sizes, most wheel builders choose the shorter one.
- A spoke that is too long runs out of thread. A spoke that is too short does not engage enough thread in the nipple.
- If in doubt, order a few extra spokes in the neighbouring size.
7Which formula do we use?
The calculator uses the common formula for spoke length. It starts from three distances: half the ERD, half the pitch circle and the distance from the hub centre to the flange. The number of crossings and the number of spokes together decide the angle between the hole in the flange and the hole in the rim. Half the spoke hole diameter is taken off the result.
The result is a calculation, not a guarantee. Measure your own parts. You will find more about wheels and spokes under tech and in the encyclopaedia.
More do-it-yourself?
In the tech section you will find guides on maintaining and repairing your bike.